Motorola Service Codes

 

To enter the "secret" codes, models Motorola T180, T2288, V3688, CD930, and others. Test mode must be enabled. To check whether it is turned on, press the key in the normal mode, "#" key and hold for a few seconds, if the word appears on the screen the TEST, it's okay. Do not touch anything, to exit dial 01 #. Dialing codes necessary at a time when the phone is in normal operating mode.

If TEST word does not appear, it means that the test mode on your device is turned off. It can be enabled either by themselves, using (Motorola test card) SIM-emulator, or by contacting a specialist, having the necessary equipment and skills.

First, you need to learn how to type on the phone "break" (hereinafter, it will be denoted by p). To set "Pause", press and hold in the key for 3-4 seconds *. The display apparatus "pause" is displayed a small square.

Teams have the form pppXXXpYp, where p - pause, XXX number of variable cell (bit), the Y value (can be 1 or 0). After entering the command, press "OK". Do not forget to enter the code ppp000p1p, ppp001p1p, ppp070p0p, which allow you to edit your phone's menu to enter codes described below.

In no case do not activate the bits 207, 211 and 244.

They can result in failure of the phone.

The most useful commands:

ppp123p1p - it includes a clock (for the installation should be included in the expanded menu, phone settings). Hours reset without battery.

ppp276p1p - You can set an alarm for incoming messages (from the phone settings - Auto answer signal)

ppp272p1p - an opportunity when sending SMS to set a destination from the phone book (if it was off)

ppp203p1pOK, ppp204p1pOK, ppp205p1pOK, ppp206p1pOK - manual switching range.

ppp278p1p - includes editor ringtones (not all phones)

ppp087p1p - includes an additional phone book for a hundred rooms in the unit (to change the device - all entries will be lost)

ppp113p1p - engineering menu.

In the menu "Eng Field Options" (engineering menu) 3 teams:

1. "Active Cell" - a work ActCh channel (from 000 to 124 - a range of 900 MHz and above - already 1800 MHz), RxLev signal level (BS -105 when you chops, and the strongest I've seen it - in 039 50 m from the BS) and many other parameters.

2. "Adjacent Cells" - options 6 adjacent channels (number, level, ...).

3. "System Parameters" - the active cell parameters (including its Cell ID).

The distance to the active, ie working base station can be viewed by logging into the engineering menu of talk time (0880, 611, 511 - MTS, BeeLine and Megafon, respectively). In "Active Cell" there are additional options, one of which is "TimeAdv" gives a number that is multiplied by 550 to get the distance to the base station in meters.

In phones with firmware version S4.10.58 or higher (to view the firmware version must be in test mode, enter the command # 19), you can activate the following options:

ppp315p1p - Service (correctly works only with iOS S4.10.75 and above)

ppp331p1p - "Games" menu

ppp332p1p - Bricks game

ppp333p1p - game Tower of Hanoi

ppp334p1p - Baccarat game

ppp367p1p - calculator.

T190, T191, T205 (Acer)

 

These phones do not have anything to do with the previous Motorola phones (except the inscriptions "Motorola" in the enclosures). To unlock these phones do not need to Emmi Box. Removing a user lock, it is also produced as in Alcatel phones using the master code.

* # 0000 # OK - default settings

* # 0007 # OK - choice of the Russian language (if it is not in the firmware will be set to English)

* # 300 # OK - firmware version

* # 301 # OK - check phone functionality, keyboard test, display, speaker.

* # 302 # OK - menu "acoustic"

* # 307 # OK - engineering menu

* # 311 # OK - phone code reset for T205

 

C350, C350L, C450, C550

 

To access the service menu must quickly press a combination of the following buttons: Menu 048 263 *. You should see an invitation to enter commands: Opcode: __________

Then you can enter commands:

54 * 0 * 0 * 0 0 tone selection

54 * 0 * 0 * 1 1 Tone selection

54 * 0 * 0 * 2 Tone selection 2

54 * 0 * 0 * 3 choice of 3 colors

54 * 0 * 0 * 4 range of tones 4

54 * 0 * 0 * 5 choice of colors 5

54 * 0 * 0 * 6 selection tone 6

54 * 0 * 0 * 7 colors choice 7

54 * 0 * 0 * 8 range of 8 colors

54 * 0 * 0 * 9 9 Tone selection

54 * 0 * 0 * 124 range of 1 KHz tone

54 * 0 * 0 * 125 KHz range of tone 2

54 * 0 * 0 * 126 range of 3 KHz tone

54 * 0 * 0 * 127 KHz range of tone 4

54 * 0 * 1 * X X tones off

54 * 3 * 0 * 1 on vibrator

54 * 3 * 0 * 0 Off vibrator

54 * 4 * 3 * 1 Enable speech coder full rate Audio loopback (including FR)

54 * 4 * 3 * 0 Disable speech coder full rate (OFF FR)

54 * 4 * 4 * 1 Enable speech coder enhanced full rate (EFR inclusion)

54 * 4 * 4 * 0 Disable speech coder enhanced full rate (EFR off)

54 * 4 * 5 * 1 Enable speech coder half rate (including HR)

54 * 4 * 5 * 0 Disable speech coder half rate (OFF HR)

54 * 5 * 0 * 0 0 sound level

54 * 5 * 0 * 1 sound level 1

54 * 5 * 0 * 2 Audio Layer 2

54 * 5 * 0 * 3 sound level 3

54 * 5 * 0 * 4 Sound level 4

54 * 5 * 0 * 5 sound level 5

54 * 5 * 0 * 6 Sound level 6

54 * 5 * 0 * 7 sound level 7

54 * 5 * 0 * 8, the sound level 8

54 * 5 * 0 * 9 sound level 9

54 * 5 * 0 * 10 sound level 10

54 * 5 * 0 * 11 sound level 11

54 * 5 * 0 * 12 sound level 12

54 * 5 * 0 * 13 sound level 13

54 * 5 * 0 * 14 sound level 14

54 * 5 * 0 * 15 sound level 15

54 * 10 * 0 * 3 GSM 900 band

54 * 10 * 0 * 4 DCS 1800 band

54 * 10 * 0 * 5 PCS 1900 band

54 * 10 * 0 * 6 GSM 900/1800 range

54 * 10 * 1 * 0 is used to see the GSM 3 = 4 = 5 = PCS the DCS 6 = GSM / DCS

54 * 18 * 0 full reset parameters (Master Reset)

54 * 18 * 1 full reset parameters with cleaning (Master Clear)

54 * 55 * 2 * 001 display test. All pixels included

54 * 55 * 2 * 000 Test display. All pixels are turned off

54 * 55 * 2 * 002 display test.

54 * 55 * 2 * 003 display test. Chess board.

54 * 55 * 2 * 004 display test. Frame.

C using the service teams in Motorola Cxxx phones can also view the phone code (user), the security code (security), as well as change the phone's IMEI:

In test mode,

32 * 4 * 1 * 0 * 0 "OK"

We get: "Results"

F1: 0; The code of the command (0, Everything OK)

F2 (D):; Data

083a05092700247709

Decrypts 08 -Required cap

3a September 5 27 00 24 77 09 - obtain IMEI -> 350,907,200,427,799

User code

32 * 116 * 1 * 0 * 0

We get: "Results"

F1: 0

F2 (D):

00310032003300340000

decrypts:

0031 -> "1"

0032 -> "2"

0033 -> "3"

0034 -> "4"

Security code - 32 * 118 * 1 * 0 * 0

Change the value can be as follows:

47 * 4 * 1 * 0 * 9 * 081A32547698103254 -> IMEI = 123456789012345

Those. You can change the IMEI, User code, Security code directly from the keyboard.

Motorola E365:

 

# 02 # Checking version

# 03 # -monitoring networks

# 04 # -monitoring battery

# 09 # -test buttons, sound, screen

** 0101 # - test sim

** 0102 # - WARNING !!! fmgr format (format)

** 0105 # - engineer menu off

** # 0106 - engineering menu (the font does not change !!!)

** 0108 # - failure counter (error counter)

* 073887 * - unlock sim. Password entry "000000"

 

MPX-200

 

Engineering menu:

* # ** 837 # Version info

* # ** 372 # FQC

* # ** 364 # Engineering menu

* # ** 266 * 0 # Set as data COM port

** # * 266 * 1 # Set as log COM port

* # ** 797 # Time to failure timer & Power down code

* # ** 2263 * 0 # Set to default Band

* # ** 2263 * 1 # Disable GSM Band

* # ** 2263 * 2 # Disable DCS Band

* # ** 2263 * 3 # Disable EGSM and DCS Band

* # ** 2263 * 4 # Disable PCS Band